福州EPS梁托的焊接工藝：

1．焊接點的焊縫寬度不能少于5mm，長度不少于連接筋直徑的4倍，打掃干凈焊渣。

2．焊接點均應涂紅丹防銹漆打底面涂銀色油漆。

3．焊接點與回填或補縫的完成面小于10mm的保護層。

福州EPS梁托的回填工藝：

1．回填的目的是把GRC構件與主體連接成一個整體，以免與主體間的接縫開裂。

2．回填時，需要對回填面的廢渣雜物打掃干凈，淋透水后才能回填，并用鋼筋或竹竿翻插回填料使其密實，不能有空殼。大飾線（離主體1250px以上）回填料需使用陶粒混凝土或膨脹珍珠巖做底層填充料，離完成面50px處用防水油膏做好墻與填充料的防水處理，然后表面用M5砂漿回填收光。回填料收水后，應處理好回填構件的結合縫（以免出現回填料與主體、構件脫接以防水）。飾線、柱頂等構件的回填面還需要按8%找坡水泥膏壓光，做到光滑不能有積水。

3．當飾線垂直距離在375px以下時，可進行回填，在15到35厘米時需分兩資回填，在875px以上時需分三次回填，以免因回填次數少、重量大而造成變形和填充料下沉開裂。